Naman Goyal, Banibrata Mukhopadhyay, Ashish Kumar Meena
We investigate the extent to which pseudo-Newtonian gravitational potentials can reproduce classic tests of general relativity without resorting to full general relativistic formalisms. This is useful for the researchers seeking intuitive insight into relativistic gravity. Focusing on the perihelion precession of Mercury, gravitational redshift, and gravitational light bending, we derive analytical expressions for orbital precession and demonstrate that, with suitable physically acceptable parameters, pseudo-Newtonian approaches can accurately reproduce the observed perihelion advance and gravitational redshift. However, we confirm that no single potential consistently captures all relativistic effects. In particular, while certain parameters yield agreement with general relativity for planetary motion and redshift, they fail to reproduce gravitational lensing over a broad range of impact parameters. Our results highlight both the usefulness and limitations of pseudo-Newtonian methods in modeling gravitational phenomena. Although the pseudo-Newtonian approach cannot serve as universal substitutes for general relativity, especially in strong-field regimes, it provides valuable semi-analytical insight and pedagogical simplicity. Our results indicate the usefulness of the pseudo-Newtonian approach to uncover more complicated phenomena involved with strong field gravity in possibly modification to general relativity.
To address the technical challenge of high polymer gel viscosity reducers losing viscosity at elevated temperatures and difficulty in controlling fluid loss, a polymer-based nano calcium carbonate composite high-temperature tackifier named GW-VIS was prepared using acrylamide (AM), 2-acrylamido-2-methylpropanesulfonic acid (AMPS), N-vinylpyrrolidone (NVP), and nano calcium carbonate as raw materials through water suspension polymerization. This polymer gel can absorb water well at room temperature and has a small solubility. After a long period of high-temperature treatment, most of it can dissolve in water, increasing the viscosity of the suspension. The structure of the samples was characterized by infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy, and their performance was evaluated. Rheological tests indicated that the 0.5% water suspension had a consistency coefficient (k = 761) significantly higher than the requirement for clay-free drilling fluids (k > 200). In thermal resistance experiments, the material maintained stable viscosity at 180 °C (reduction rate of 0%), and only decreased by 14.8% at 200 °C. Salt tolerance tests found that the viscosity reduction after hot rolling at 200 °C was only 17.31% when the NaCl concentration reached saturation. Field trials in three wells in the Liaohe oilfield verified that the clay-free drilling fluid supported formation operations successfully. The study shows that the polymer gel has the potential to maintain rheological stability at high temperatures by forming a network structure through polymer chain adsorption and entanglement, with a maximum temperature resistance of up to 200 °C, providing an efficient drilling fluid for deep oil and gas well development. It is feasible to select nano calcium carbonate to participate in the research of high-temperature resistant polymer materials. Meanwhile, the combined effect of monomers with large steric hindrance and inorganic materials can enhance the product’s temperature resistance and resistance to NaCl pollution.
In the past, powder-like microwave absorbers have made notable breakthroughs in performance enhancements, but complicated processes and undesirable properties have limited their practical application. Herein, a novel poly(ionic liquid) (PIL)-based ionic gel with excellent microwave absorption properties was prepared via a facile UV-initiated polymerization method. By simply adjusting the mole ratio of the polymerizable ionic liquid (IL)monomer and the IL dispersion medium, the microwave absorption properties of the obtained ionic gels can be tuned. A maximum reflection loss (RL<sub>max</sub>) of −45.7 dB and an effective absorption bandwidth (EAB) of 8.08 GHz were achieved, which was mainly ascribed to high ionic conduction loss induced by the high content of the dispersion medium. Furthermore, it displayed recyclable, adhesive, and self-healing properties, thus providing a new candidate for developing efficient microwave absorbers for practical applications.
The comonomer bisphenol A (BPA) finds applications in the plastics industry, where it is used in the production of polycarbonates, plastics, PVC, thermal paper, epoxy and vinyl ester resins, and polyurethane. The water, with which many of these materials come into contact, is one of the main sources of human exposure to BPA. When ingested or touched, BPA can damage organs, disrupt the endocrine and immune systems, generate inflammatory responses, and be involved in genotoxic processes. Therefore, the need to develop effective techniques for removing BPA from aqueous environments is imperative. This paper provides a comprehensive review regarding the effective removal of BPA from water, focusing on the performance and adsorption mechanisms of various adsorbents based on chitosan and chitosan composites. The chemical and physical factors, adsorption kinetics and models governing the adsorption process of BPA in chitosan materials are also examined. This review outlines that, despite considerable progress in the absorption of bisphenol using chitosan gels, further research is necessary to assess the efficacy of these adsorbents in treating real wastewater and in large-scale manufacture.
Hien Vinh Nguyen, Phong Xuan Huynh, Tuyen Chan Kha
This study investigated the effects of ultrasound treatment on the physicochemical properties and thermal stability of durian starch. Durian starch samples were subjected to ultrasound at 20 kHz and 500 W for 2 min. The treatment significantly increased the starch extraction yield by 14.55% compared to untreated starch. Scanning electron microscopy analysis revealed that ultrasound treatment induced physical modifications in the starch granules, including the formation of cracks and pores, which likely contributed to the enhanced extraction efficiency and influenced the starch’s gelation behavior. Thermal analysis, including differential scanning calorimetry and thermogravimetric analysis, demonstrated that ultrasound-treated starch exhibited higher thermal stability compared to native starch. The thermogravimetric analysis results indicated a lower weight loss at high temperatures (70.39% for ultrasound-treated starch versus 79.55% for native starch at 596 °C). The heat flow during thermal decomposition was reduced in ultrasound-treated starch, suggesting that the treatment induced structural modifications that strengthened the gel matrix and improved resistance to thermal degradation. Additionally, ultrasound treatment enhanced the functional properties of durian starch, including swelling power, solubility, and water absorption capacity, which are critical for hydrogel formation and food-grade gel applications. These findings highlight the potential of ultrasound-treated durian starch for advanced applications in food hydrogels, biodegradable films, and gel-based delivery systems.
Cellulose nanofibrils (CNFs) are promising materials for flexible and green supercapacitor electrodes, while Ti<sub>3</sub>C<sub>2</sub>T<sub>x</sub> MXene exhibits high specific capacitance. However, the diffusion limitation of ions and chemical instability in the generally used highly basic (KOH, MXene oxidation) or acidic (H<sub>2</sub>SO<sub>4</sub>, CNF degradation) electrolytes limits their performance and durability. Herein, freestanding CNF/MXene cryogel membranes were prepared by deep freeze-casting (at −50 and −80 °C), using different weight percentages of components (10, 50, 90), and evaluated for their structural and physico-chemical stability in other less aggressive aqueous electrolyte solutions (Na<sub>2</sub>/Mg/Mn/K<sub>2</sub>-SO<sub>4</sub>, Na<sub>2</sub>CO<sub>3</sub>), to examine the influence of the ions transport on their pseudocapacitive properties. While the membrane prepared with 50 wt% (2.5 mg/cm<sup>2</sup>) of MXene loading at −80 °C shrank in a basic Na<sub>2</sub>CO<sub>3</sub> electrolyte, the capacitance was performed via the forming of an electroactive layer on its interface, giving it high stability (90% after 3 days of cycling) but lower capacitance (8 F/g at 2 mV/s) than in H<sub>2</sub>SO<sub>4</sub> (25 F/g). On the contrary, slightly acidic electrolytes extended the cations’ transport path due to excessive but still size-limited diffusion of the hydrated ions (SO<sub>4</sub><sup>2−</sup> > Na<sup>+</sup> > Mn<sup>2+</sup> > Mg<sup>2+</sup>) during membrane swelling, which blocked it, reducing the electroactive surface area and lowering conductivities (<3 F/g).
Giovanni Venturelli, Federica Villa, Mariagioia Petraretti
et al.
Microbial-derived materials are emerging for applications in biomedicine, sensors, food, cosmetics, construction, and fashion. They offer considerable structural properties and process reproducibility compared to other bio-based materials. However, challenges related to efficient and sustainable large-scale production of microbial-derived materials must be addressed to exploit their potential fully. This review analyzes the synergistic contribution of circular, sustainable, and biotechnological approaches to enhance bacterial cellulose (BC) production and fine-tune its physico-chemical properties. BC was chosen as an ideal example due to its mechanical strength and chemical stability, making it promising for industrial applications. The review discusses upcycling strategies that utilize waste for microbial fermentation, simultaneously boosting BC production. Additionally, biotechnology techniques are identified as key to enhance BC yield and tailor its physico-chemical properties. Among the different areas where cellulose-based materials are employed, BC shows promise for mitigating the environmental impact of the garment industry. The review emphasizes that integrating circular and biotechnological approaches could significantly improve large-scale production and enhance the tunability of BC properties. Additionally, these approaches may simultaneously provide environmental benefits, depending on their future progresses. Future advancements should prioritize circular fermentation and biotechnological techniques to expand the potential of BC for sustainable industrial applications.
This research aimed to evaluate the efficacy of a nanoemulgel (NE) containing <i>Cananga odorata</i> (Ylang-Ylang) oil for managing scalp psoriasis and dandruff through various assessments. The study involved phytochemical screening, characterization, stability testing, in vivo performance evaluation, dermatokinetic analysis, central composite rotatable design (CCRD) optimization, in vitro release profiling, and antioxidant and antimicrobial activity assessment of the NE. The NE exhibited excellent stability and maintained physical parameters over a three-month period. In vivo studies showed no skin irritation, maintenance of skin pH (4.55 to 5.08), and improvement in skin hydration (18.09 to 41.28 AU) and sebum content (26.75 to 5.67 mg/cm<sup>2</sup>). Dermatokinetic analysis revealed higher skin retention of <i>C. odorata</i> in the NE (epidermis: 71.266 µg/cm<sup>2</sup>, dermis: 60.179 µg/cm<sup>2</sup>) compared to conventional formulations. CCRD optimization yielded NE formulations with the desired particle size (195.64 nm), entrapment efficiency (85.51%), and zeta potential (−20.59 mV). In vitro release studies indicated sustained release behavior, and antioxidant and antimicrobial properties were observed. This study demonstrates the stability, skin-friendliness, therapeutic benefits, and controlled release properties of the NE. The NE presents a promising option for various topical applications in treating bacterial and fungal diseases, potentially enhancing drug delivery and treatment outcomes in pharmaceuticals and cosmetics.
Anastasia Korel, Alexander Samokhin, Ekaterina Zemlyakova
et al.
To date, few publications describe CEC’s properties and possible applications—thus, further evaluation of these properties is a point of interest. The present in vitro model study aimed to evaluate a carboxyethylchitosan (CEC) gel with a degree of substitution of 1, cross-linked with glutaraldehyde at a polymer:aldehyde molar ratio of 10:1, as a potential carrier for delivering bacteriophages to various pH-fixed media (acidic, alkaline), and including gastrointestinal tract (GIT) variable medium. A quantitative analysis of bacteriophages released from the gel was performed using photon correlation spectrophotometry, and phage activity after emission into medium was evaluated using the spot test. The results showed that the CEC gel’s maximum swelling ratios were at a nearly neutral alkaline pH. Increasing temperature enhances the swelling ratio of the gel independent from pH, up to 1127% at 37 °C and alkaline pH. The UV and photon correlation spectrophotometry showed equal gel release kinetics in both fixed media with acidic (pH = 2.2) and alkaline (pH = 7.4) pH environments at 37 °C, with the maximum release within two hours. However, phage lytic activity in the spot test during this simulation was absent. At the same time, we obtained an opaque phage lytic activity in the alkaline pH-fixed medium for at least three hours. Phages released from the tested CEC gel in different pHs suggest that this gel could be used for applications that require fast release at the treatment site both in acidic and alkaline pH. Such treatment sites could be a wound or even soil with mild acidic or alkaline pH. However, such CEC gel is not suitable as a delivery system to the GIT because of possible transported acid-sensitive agent (such as phages) release and destruction already in the stomach.
Badr M. Thamer, Meera Moydeen Abdul Hameed, Mohamed H. El-Newehy
The preparation of metallic nanostructures supported on porous carbon materials that are facile, green, efficient, and low-cost is desirable to reduce the cost of electrocatalysts, as well as reduce environmental pollutants. In this study, a series of bimetallic nickel–iron sheets supported on porous carbon nanosheet (NiFe@PCNs) electrocatalysts were synthesized by molten salt synthesis without using any organic solvent or surfactant through controlled metal precursors. The as-prepared NiFe@PCNs were characterized by scanning and transmission electron microscopy (SEM and TEM), X-ray diffraction, and photoelectron spectroscopy (XRD and XPS). The TEM results indicated the growth of NiFe sheets on porous carbon nanosheets. The XRD analysis confirmed that the Ni<sub>1−x</sub>Fe<sub>x</sub> alloy had a face-centered polycrystalline (fcc) structure with particle sizes ranging from 15.5 to 30.6 nm. The electrochemical tests showed that the catalytic activity and stability were highly dependent on the iron content. The electrocatalytic activity of catalysts for methanol oxidation demonstrated a nonlinear relationship with the iron ratio. The catalyst doped with 10% iron showed a higher activity compared to the pure nickel catalyst. The maximum current density of Ni<sub>0.9</sub>Fe<sub>0.1</sub>@PCNs (Ni/Fe ratio 9:1) was 190 mA/cm<sup>2</sup> at 1.0 M of methanol. In addition to the high electroactivity, the Ni<sub>0.9</sub>Fe<sub>0.1</sub>@PCNs showed great improvement in stability over 1000 s at 0.5 V with a retained activity of 97%. This method can be used to prepare various bimetallic sheets supported on porous carbon nanosheet electrocatalysts.
Quasi-dry CO<sub>2</sub> fracturing technology is a new CO<sub>2</sub> fracturing technology that combines liquid CO<sub>2</sub> fracturing (dry CO<sub>2</sub> fracturing) and water-based fracturing. It uses a liquid CO<sub>2</sub> system containing a small amount of water-based fracturing fluid to carry sand, and it is characterized by sand blending at normal pressure, convenient preparation, the integrated application of resistance reduction and sand carrying, and no dedicated closed sand blender requirement. We developed a self-crosslinking emulsion-type water-based fracturing fluid (ZJL-1), which contained ionic bonds, hydrogen bonds, van der Waals forces, and hydrophobic associations, for quasi-dry CO<sub>2</sub> fracturing, and the comprehensive properties of the ZJL-1 fracturing fluid were evaluated. The results showed that the ZJL-1 fracturing fluid had obvious viscoelastic characteristics, a heat loss rate of less than 10% at 200 °C, a good thermal stability, sufficient rheology under high temperature and high shear conditions, and a good thermal stability. The resistance reduction rate reached 70%, which demonstrates a good resistance reduction performance. Compared with conventional guar fracturing fluid, ZJL-1 can carry more sand and has a lower core damage rate. The on-site use of quasi-dry fracturing showed that optimizing the mixing ratio of liquid CO<sub>2</sub> fracturing fluid and ZJL-1 fracturing fluid effectively enhanced oil and gas recovery. This can be used to optimize quasi-dry fracturing and can be used as a reference.
Sulaiman Mohammed Alnasser, Faizul Azam, Mohammed H. Alqarni
et al.
In recent years, methicillin-resistant <i>Staphylococcus aureus</i> (MRSA) bacteria have seriously threatened the health and safety of the world’s population. This challenge demands the development of alternative therapies based on plant origin. This molecular docking study ascertained the orientation and intermolecular interactions of isoeugenol within penicillin-binding protein 2a. In this present work, isoeugenol as an anti-MRSA therapy was selected by encapsulating it into a liposomal carrier system. After encapsulation into the liposomal carrier, it was evaluated for encapsulation efficiency (%), particle size, zeta potential, and morphology. The percentage entrapment efficiency (% EE) was observed to be 57.8 ± 2.89% with a particle size of 143.31 ± 7.165 nm, a zeta potential of (−)25 mV, and morphology was found to be spherical and smooth. After this evaluation, it was incorporated into a 0.5% Carbopol gel for a smooth and uniform distribution on the skin. Notably, the isoeugenol-liposomal gel was smooth on the surface with a pH of 6.4, suitable viscosity, and spreadability. Interestingly, the developed isoeugenol-liposomal gel was safe for human use, with more than 80% cell viability. The in vitro drug release study shows promising results with 75.95 ± 3.79% of drug release after 24 h. The minimum inhibitory concentration (MIC) was 8.236 µg/mL. Based on this, it can be concluded that encapsulating isoeugenol into the liposomal gel is a potential carrier for MRSA treatment.
Murat Shagidulin, Nina Onishchenko, Victor Sevastianov
et al.
Our study sought approaches for chronic liver failure (CLF) treatment and correction via cell-engineered constructs (CECs). They are built from biopolymer-based, microstructured, and collagen-containing hydrogel (BMCG). We also strove to evaluate the functional activity of BMCG in liver regeneration. Materials and Methods: Allogeneic liver cells (namely, hepatocytes; LC) together with mesenchymal multipotent stem cells of bone marrow origin (MMSC BM; BMSCs) were adhered to our BMCG to compose implanted liver CECs. Thereafter, we investigated a model of CLF in rats receiving the implanted CECs. The CLF had been provoked by long-term exposure to carbon tetrachloride. The study comprised male Wistar rats (<i>n</i> = 120) randomized into 3 groups: Group 1 was a control group with the saline treatment of the hepatic parenchyma (<i>n</i> = 40); Group 2 received BMCG only (<i>n</i> = 40); and Group 3 was loaded with CECs implanted into the parenchyma of their livers (<i>n</i> = 40). August rats (<i>n</i> = 30) made up a donor population for LCs and MMSC BM to develop grafts for animals from Group 3. The study length was 90 days. Results: CECs were shown to affect both biochemical test values and morphological parameters in rats with CLF. Conclusion: We found BMCG-derived CECs to be operational and active, with regenerative potential. Group 3 showed significant evidence of forced liver regeneration that tended to persist until the end of the study (day 90). The phenomenon is reflected by biochemical signs of hepatic functional recovery by day 30 after grafting (compared to Groups 1 and 2), whereas structural features of liver repair (necrosis prevention, missing formation of vacuoles, degenerating LC number decrease, and delay of hepatic fibrotic transformation). Such implantation of BMCG-derived CECs with allogeneic LCs and MMSC BM might represent a proper option to correct and treat CLF, as well as to maintain affected liver function in patients with liver grafting needed.
Paweł Kubik, Daniela Gallo, Maria Laura Tanda
et al.
The aim of this study was to test the effect of hyaluronic acid cross-linked with polyethylene glycol containing micronized portions of calcium hydroxyapatite (Neauvia Stimulate) on both local tissue and systemic consequences, which are crucial from the perspective of long-term safety, in patients suffering from Hashimoto’s disease. This most common autoimmune disease is a frequently mentioned contraindication to the use of fillers based on hyaluronic acid as well as biostimulants based on calcium hydroxyapatite. Broad-spectrum aspects of histopathology were analyzed to identify key features of inflammatory infiltration before the procedure and 5, 21, and 150 days after the procedure. A statistically significant effect on the reduction of the intensity of the inflammatory infiltration in the tissue in relation to the state before the procedure was demonstrated, combined with a reduction in the occurrence of both antigen-recognizing (CD4) and cytotoxic (CD8) T lymphocytes. With complete statistical certainty, it was demonstrated that the treatment with Neauvia Stimulate had no effect on the levels of these antibodies. All this corresponds with the risk analysis that showed no alarming symptoms during the time of observation. The choice of hyaluronic acid fillers cross-linked with polyethylene glycol should be considered justified and safe in the case of patients suffering from Hashimoto’s disease.
Oil-based drilling fluids are widely used in challenging wells such as those with large displacements, deepwater and ultra-deepwater wells, deep wells, and ultra-deep wells due to their excellent temperature resistance, inhibition properties, and lubrication. However, there is a challenging issue of rheological deterioration of drilling fluids under high-temperature conditions. In this study, a dual-amphiphilic segmented high-temperature-resistant gelling agent (HTR-GA) was synthesized using poly fatty acids and polyether amines as raw materials. Experimental results showed that the initial decomposition temperature of HTR-GA was 374 °C, indicating good thermal stability. After adding HTR-GA, the emulsion coalescence voltage increased for emulsions with different oil-to-water ratios. HTR-GA could construct a weak gel structure in oil-based drilling fluids, significantly enhancing the shear-thinning and thixotropic properties of oil-based drilling fluids under high-temperature conditions. Using HTR-GA as the core, a set of oil-based drilling fluid systems with good rheological properties, a density of 2.2 g/cm<sup>3</sup>, and temperature resistance up to 220 °C were constructed. After aging for 24 h at 220 °C, the dynamic shear force exceeded 10 Pa, and G′ exceeded 7 Pa, while after aging for 96 h at 220 °C, the dynamic shear force exceeded 4 Pa, and G″ reached 7 Pa. The synthesized compound HTR-GA has been empirically validated to significantly augment the rheological properties of oil-based drilling fluids, particularly under high-temperature conditions, showcasing impressive thermal stability with a resistance threshold of up to 220 °C. This notable enhancement provides critical technical reinforcement for progressive exploration endeavors in deep and ultra-deep well formations, specifically employing oil-based drilling fluids.
We integrate foundational theories of meaning with a mathematical formalism of artificial general intelligence (AGI) to offer a comprehensive mechanistic explanation of meaning, communication, and symbol emergence. This synthesis holds significance for both AGI and broader debates concerning the nature of language, as it unifies pragmatics, logical truth conditional semantics, Peircean semiotics, and a computable model of enactive cognition, addressing phenomena that have traditionally evaded mechanistic explanation. By examining the conditions under which a machine can generate meaningful utterances or comprehend human meaning, we establish that the current generation of language models do not possess the same understanding of meaning as humans nor intend any meaning that we might attribute to their responses. To address this, we propose simulating human feelings and optimising models to construct weak representations. Our findings shed light on the relationship between meaning and intelligence, and how we can build machines that comprehend and intend meaning.
<p>A clear legal test for equality is impossible, as it should be. Indeed were the test clear, it could not be for equality. It would have to be for something other than equality — in effect, for inequality. The abstract character of equality is not a new idea. In fact, the Supreme Court of Canada’s first decision under section 15 of the Canadian Charter of Rights and Freedoms recognized equality as “an elusive concept” that “lacks precise definition.” Why, then, do judges continue to demand such definition over thirty years later? The answer, at times, is politics.</p>
Although hydrogel is a promising prosthesis implantation material for breast reconstruction, there is no suitable hydrogel with proper mechanical properties and good biocompatibility. Here, we report a series of compliant and tough poly (hydroxyethyl methacrylate) (PHEMA)-based hydrogels based on hydrogen bond-reinforcing interactions and phase separation inhibition by introducing maleic acid (MA) units. As a result, the tensile strength, fracture strain, tensile modulus, and toughness are up to 420 kPa, 293.4%, 770 kPa, and 0.86 MJ/m<sup>3</sup>, respectively. Moreover, the hydrogels possess good compliance, where the compression modulus is comparable to that of the silicone breast prosthesis (~23 kPa). Meanwhile, the hydrogels have an excellent self-recovery ability and fatigue resistance: the dissipative energy and elastic modulus recover almost completely after waiting for 2 min under cyclic compression, and the maximum strength remains essentially unchanged after 1000 cyclic compressions. More importantly, in vitro cellular experiments and in vivo animal experiments demonstrate that the hydrogels have good biocompatibility and stability. The biocompatible hydrogels with breast tissue-like mechanical properties hold great potential as an alternative implant material for reconstructing breasts.
Calcium silicate hydrate (CSH) gels, the main binding phases of hydrated cement, are the most widely utilized synthetic materials. To understand the influences of composition and polymers on the reaction kinetics and phase formation, CSH gels with varying Ca/Si ratios and amounts of poly (acrylamide-co-acrylic acid) partial sodium salt (PAAm-co-PAA) were synthesized via a direct method. The CSH gels were characterized through isothermal calorimetry, thermogravimetric analysis (TGA), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and Raman spectroscopy at different ages. By increasing the Ca/Si ratio from 0.8 to 1.0, the formation of CSH was enhanced with a 5.4% lower activation energy, whereas the incorporation of PAAm-co-PAA increased the temperature sensitivity of the reactions with an 83.3% higher activation energy. In the presence of PAAm-co-PAA, the reaction rate was retarded at an early age and the negative impact faded over time. The results of an XRD analysis indicated the formation of tobermorite as the main phase of the CSH gels, while the addition of PAAm-co-PAA resulted in a postponed calcium hydroxide consumption and CSH formation, which was confirmed by the decreased FTIR intensity of the C=O bond, Si–O stretching and Si–O bonds. The increased Raman vibrations of Si–O–Si bending Q<sup>2</sup>, Ca–O bonds, O–Si–O and asymmetric bending vibrations of SiO<sub>4</sub> tetrahedra in the presence of PAAm-co-PAA indicate the intercalation of the polymeric phase and internal deformation of CSH gels.
In this study, chitosan (CS) and 2-acrylamido-2-methylpropane sulfonic acid (AMPS)-based hydrogels were formulated by the free radical polymerization technique for the controlled release of gallic acid. Fourier transform infrared spectroscopy (FTIR) confirmed the successful preparation and loading of gallic acid within the hydrogel network. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) confirmed the increased thermal stability of the hydrogels following the crosslinking and polymerization of chitosan and AMPS. In X-ray diffraction analysis (XRD), the crystallinity of the raw materials decreased, indicating strong crosslinking of the reagents and the formation of a new polymeric network of hydrogels. Scanning electron microscopy (SEM) revealed that the hydrogel had a rough, dense, and porous surface, which is consistent with the highly polymerized composition of the hydrogel. After 48 h, the hydrogels exhibited higher swelling at pH 1.2 (swelling ratio of 19.93%) than at pH 7.4 (swelling ratio of 15.65%). The drug release was analyzed using ultraviolet-visible (UV-Vis) spectrophotometer and demonstrated that after 48 h, gallic acid release was maximum at pH 1.2 (85.27%) compared to pH 7.4 (75.19%). The percent porosity (78.36%) and drug loading increased with the increasing concentration of chitosan and AMPS, while a decrease was observed with the increasing concentration of ethylene glycol dimethyl methacrylate (EGDMA). Crosslinking of the hydrogels increased with concentrations of chitosan and EGDMA but decreased with AMPS. In vitro studies demonstrated that the developed hydrogels were biodegradable (8.6% degradation/week) and had antimicrobial (zone of inhibition of 21 and 16 mm against Gram-positive bacteria <i>Escherichia coli</i> and <i>Staphylococcus aureus</i> as well as 13 mm against Gram-negative bacteria <i>Pseudomonas aeruginosa</i>, respectively) and antioxidant (73% DPPH and 70% ABTS) properties. Therefore, the prepared hydrogels could be used as an effective controlled drug delivery system.